Provides a container of all Revit built-in FailureDefinitionId instances.
The BuiltInFailuresAnalyticalModelFailures type exposes the following members.
Properties
| Name | Description | |
|---|---|---|
  | AdjustCurveTooShort | AdjustCurve is too short. |
| AdjustEdgeTooShort | AdjustEdge is too short. |
| AdjustEdgeTooShortErr | AdjustEdge is too short - continuable error version. |
| AdjustEdgeTooShortWarn | AdjustEdge is too short. |
| AnalyticalBeamSlabWarning | Beam and Slab Analytical Models do not have the same Analytical Projection Plane. |
| AnalyticalCurvedPanelNotValid | Analytical Curved Panel is not valid. |
| AnalyticalDiscrepancyWarning | Distance between Analytical and Physical Models of Structural Element is beyond tolerance of [Value] |
| AnalyticalElementsInvalidAfterUpgrade | One or several analytical elements have become invalid during the upgrade process and will be deleted. |
| AnalyticalGapWarning | Detected physical connection between Structural Elements, but did not detect Analytical intersection. |
| AnalyticalLinkJoinedNodes | Analitycal Link is invalid. Reference nodes have been joined. |
| AnalyticalLinkNotConnected | Analytical Link has lost one or more references. |
| AnalyticalMemberInstability | Possible Member Instability, based on Release Conditions |
| AnalyticalModelInstability | Possible Model Instability |
| AnalyticalModelIsIncorrect | Analytical Model is not created for the structural element. |
| AnalyticalPanelNotPlanar | Analytical Panel is not planar. |
| AnalyticalPanelNotVisible | Analytical Panel is not visible in the current view. |
| AnalyticalPhysicalCheckDone | Analytical / Physical Model Consistency check is complete. |
| AnalyticalSupportCycleWarning | Circular support chain detected |
| AnalyticalSurfaceCannotMove | Cannot move analytical surface. |
| AnalyticalSurfaceCannotMoveByConnector | Cannot move analytical surface because it will disconnect the analytical nodes. |
| AnalyticalTopBottomPlanesReversed | Analytical Top Projection Plane is partially or completely below Analytical Bottom Projection Plane. Please reset top and/or bottom planes to valid values. |
| AutoDetectIgnoreLeaderWarning | Analytical Model for Structural Element has reset to its default location. |
| BoundaryLinesIntersect | Boundary lines intersect. |
| CannotCreateAnalyticalGeometry | Cannot construct Analytical Geometry. |
| CannotKeepAnalyticalAdjustment | Analytical model Adjustment distance exceeds current Adjustment Snapping Distance. To adjust snap settings, go to the Structural Settings Dialog. |
| CannotMakeAnalyticalGeometry | Cannot construct Analytical Geometry. |
| CannotSlantAnalyticalWallError | Cannot slant a wall with an Analytical Model. Please disable the Analytical Model first. |
| ContextualAnalyticalModelModeNotEnabled | Contextual Analytical Model not enabled. File open was canceled. |
| HighestAssociatedLevelBelowLowestAssociatedLevel | The Highest Associated Level is set below the Lowest Associated Level |
| LoadsMayBeNotUpToDate | Reactions defined as Internal Load (Is Reaction) may no longer be valid since the analytical model has changed. |
| LowestAssociatedLevelAboveHighestAssociatedLevel | The Lowest Associated Level is set above the Highest Associated Level |
| ProjectionPlaneInvalidWall | Projection plane becomes invalid for this wall. |
| ProjectionPlanesNotIntersect | Can't project Analytical Model. Planes do not intersect each other. |
| ProjectionPlanesParallel | Can't project Analytical Model. Two or more projection planes are parallel. |
| StructAnalyticalErrorProjection | Can't project Analytical Model to Analytical Projection Surface |
| StructuralElementMayNotBeSupported | Structural Element may not be supported -- verify support for Element. |
| StructWallAnalyticalErrorAlign | Can't align Analytical Model with joined Walls. |
| StructWallAnalyticalErrorConversion | Can't convert Edges to Analytical Model curves. |
| SupportCheckDone | Member support check is complete. No unsupported elements detected. |
| UnableToUpgradeAnalyticalElementGeometry | Unable to upgrade analytical element with incorrect geometry. To keep the elements, open Revit 2022 and correct the elements. |
| WallAMLostAdjustmentReference | Wall Analytical Model has lost its adjustment reference. |