•  

BuiltInFailures.MEPFabricationFailures Class

Built In Failures MEPFabrication Failures Class

Failures about MEP fabrication.
Inheritance Hierarchy
System Object
Autodesk.Revit.DB BuiltInFailures MEPFabricationFailures

Namespace: Autodesk.Revit.DB
Assembly: RevitAPI (in RevitAPI.dll) Version: 25.0.0.0 (25.0.0.0)
Syntax 
public static class MEPFabricationFailures

The BuiltInFailures MEPFabricationFailures type exposes the following members.

Properties
Name Description
Public property Static member AdditionalPartNotLoaded An additional part was not loaded.
Public property Static member CannotConvertFlexPipeToPart Cannot convert flex pipe to fabrication part.
Public property Static member CannotMatchFabricationHangerSizeToHost The hanger cannot be re-sized to match the re-sized host.
Public property Static member FabDbChangeConn Fabrication Database changes altered connectivity
Public property Static member FabDbOpenJobConn Fabrication job imported had bad connectivity
Public property Static member FabDbSwapOut Fabrication Database reload could not swap out for newer parts.
Public property Static member FabricationConfigurationCorrupted It looks that the Fabrication Configuration %1!s! was corrupted, please check it at %2!s!.
Public property Static member FabricationHangerCannotBeSloped A hanger cannot be sloped or placed on a sloped element.
Public property Static member FabricationHangerHostNotFound The hanger will disconnect because we can't find the suitable host.
Public property Static member FabricationHangerNotConnectToHost Fabrication Hanger didn't connect to the %s host.
Public property Static member FabricationHangerOutOfHost The hanger is out of its host and will be disconnected.
Public property Static member FabricationHangerSizeNotMatch The hanger size does not match the size of the host, so it can not be connected.
Public property Static member FabricationOutOfSizeCondition The fabrication part size is not within the correct size range for the service button condition.
Public property Static member FabricationOverSizedCheck Fabrication part is too large to fit on the sheet metal. Replace the part with multiple smaller parts, or notify the CAM operator.
Public property Static member FabricationPartBadConnectionAlignmentWarning The connection invalid due to the connector are not aligned and/or this is a gap between the connectors.
Public property Static member FabricationPartBadConnectionConnectivityWarning The connection invalid due to connection types associated to the connectors are not compatible.
Public property Static member FabricationPartBadConnectionSizeWarning The connection invalid due to connectors sizes are not the same.
Public property Static member FabricationPartCannotBeMirrored
Public property Static member FabricationPartCannotChangeServiceSizeWarning The selected fitting(s) cannot successfully change service or change size. You must disconnect the connections on the fitting(s) and try again.
Public property Static member FabricationPartCannotChangeSlopeError The connected fitting(s) cannot successfully change to the new slope value. You may try to disconnect the connections on the fitting(s) and try again.
Public property Static member FabricationPartCannotChangeTypeBadDimError The selected fitting(s) cannot successfully change the type. The newly selected fabrication part may have badly configured dimensions or be constrained due to connected fitting(s). You may try to disconnect the connections on the fitting(s) and try again.
Public property Static member FabricationPartCannotChangeTypeBadDimUnConnError The selected fitting(s) cannot successfully change the type. The newly selected fabrication part may have badly configured dimensions, resulting in bad geometry.
Public property Static member FabricationPartCannotChangeTypeError The selected fitting(s) cannot successfully change the type. You must disconnect the connections on the fitting(s) and try again.
Public property Static member FabricationPartCannotChangeTypeIncompatError The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type either has no material or has badly configured dimensions, resulting in bad geometry. You may try to disconnect the connections on the fitting(s) and try again.
Public property Static member FabricationPartCannotChangeTypeIncompatUnConnError The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type either has no material or has badly configured dimensions, resulting in bad geometry.
Public property Static member FabricationPartCannotChangeTypeMisalignedError The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type has a problem with the angle dimension of the current fitting(s), resulting in bad geometry. You may try to disconnect the connections on the fitting(s) and try again.
Public property Static member FabricationPartCannotChangeTypeMisalignedUnConnError The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type has a problem with the angle dimension of the current fitting(s), resulting in bad geometry.
Public property Static member FabricationPartCannotChangeTypeUnConnError The selected fitting(s) cannot successfully change the type.
Public property Static member FabricationPartCannotChangeTypeWarning The selected fitting(s) cannot maintain connections to existing fabrication parts due to size, direction or angle differences. You must manually reconnect the open connections.
Public property Static member FabricationPartExceededAngleFlexToleranceWarning The angle flex is greater than the maximum angle flex tolerance defined by the fabrication part. Connections with this part may not be properly aligned and may appear to be skewed.
Public property Static member FabricationPartExcludedPartWarning There were fabrication parts needed to the make the connection that were excluded from the fabrication service causing the connection to fail. You may try to inlcude these fitting(s) and try again.
Public property Static member FabricationPartFitFailure Fabrication Part Fitting Failed to Fit
Public property Static member FabricationPartFitFailWarning Fabrication Part Fitting Failed to Fit
Public property Static member FabricationPartHasInvalidGeometry The fabrication part either has no material or has badly configured dimensions, resulting in bad geometry.
Public property Static member FabricationPartInvalidConnection Fabrication Part connection invalid and could not be automatically coupled.
Public property Static member FabricationPartInvalidSpecification The part specification is invalid.
Public property Static member FabricationPartNoPartTypeFound There are no fabrication part types found for the current Configuration and Service. Please select settings and reload the service to create the fabrication part types.
Public property Static member FabricationPartNotAttachedToStraight The part must be attached to straight.
Public property Static member FabricationPartOptimizeInvalidConnection No available couplings to connect standard lengths for this instance of straight.
Public property Static member FabricationRodDetachFromHangerError The rod need to be detached from hanger.
Public property Static member FabricationRodsConnectionChangedWarning The structural component that the hanger is attached to has changed to a different element.
Public property Static member FabricationRodsDisconnectedError The hanger rod was disconnected because there is no structural component above.
Public property Static member FabricationRodsDisconnectedWarning The hanger rod was disconnected because there is no structural component above.
Public property Static member FabricationServiceMismatch Attempting to connect fabrication parts from different services.
Public property Static member FabricationStraigtLengthOversized Fabrication straight exceeds the standard length. Use the Optimize Length command to adjust the length.
Public property Static member FixedFabricationPartNotChangeLength Failed to change length of fixed part.
Public property Static member GroupedFabricationPartNotReposition Failed to reposition part.
Public property Static member HangerProfileNotMatchWithHost The defined hanger profile does not match with the host.
Public property Static member HangerWidthOutOfRange The hanger width is too large to show.
Public property Static member InvalidConnectionsHaveBeenDisconnected Invalid connections have been disconnected. Please reconnect them manually or use different fittings.
Public property Static member InvalidSelectionThereCannotBeOpenConnectors Invalid selection there cannot be any open connectors for the design to fabrication part tool.
Public property Static member NoStructuralHostToAttachWarning There is no structural component to attach the hanger rod to.
Public property Static member NotAllPartsWereConvertedUnsuportedFittingOffsets Not all parts were converted. Eccentric transitions and taps that have offsets from the center line are unsupported and cannot be converted.
Public property Static member PinnedFabricationPartNotChangeExtension Failed to change extension of part.
Public property Static member PinnedFabricationPartNotReposition Failed to reposition part.
Public property Static member PlaceCutinFittingFailed Failed to insert part.
Public property Static member SizeNotAvailableInFabricationService Sizes:%1!s! in system %2!s! are not available in fabrication service:%3!s!, All available sizes are:\n%4!s!.
Public property Static member UneditableFabricationPartNotReposition Failed to reposition part.
Top
See Also