Provides a container of all Revit built-in FailureDefinitionId instances.
The BuiltInFailures MEPFabricationFailures type exposes the following members.
Properties
Name | Description | |
---|---|---|
CannotConvertFlexPipeToPart |
Cannot convert flex pipe to fabrication part.
|
|
CannotMatchFabricationHangerSizeToHost |
The hanger cannot be re-sized to match the re-sized host.
|
|
FabDbChangeConn |
Fabrication Database changes altered connectivity
|
|
FabDbOpenJobConn |
Fabrication job imported had bad connectivity
|
|
FabricationConfigurationCorrupted |
It looks that the Fabrication Configuration %1!s! was corrupted, please check it at %2!s!.
|
|
FabricationHangerCannotBeSloped |
A hanger cannot be sloped or placed on a sloped element.
|
|
FabricationHangerHostNotFound |
The hanger will disconnect because we can't find the suitable host.
|
|
FabricationHangerNotConnectToHost |
Fabrication Hanger didn't connect to the %s host.
|
|
FabricationHangerOutOfHost |
The hanger is out of its host and will be disconnected.
|
|
FabricationHangerSizeNotMatch |
The hanger size does not match the size of the host, so it can not be connected.
|
|
FabricationOutOfSizeCondition |
The fabrication part size is not within the correct size range for the service button condition.
|
|
FabricationOverSizedCheck |
Fabrication part is too large to fit on the sheet metal. Replace the part with multiple smaller parts, or notify the CAM operator.
|
|
FabricationPartCannotBeMirrored | ||
FabricationPartCannotChangeTypeError |
The selected fitting(s) cannot successfully change the type. You must disconnect the connections on the fitting(s) and try again.
|
|
FabricationPartCannotChangeTypeWarning |
The selected fitting(s) cannot maintain connections to existing fabrication parts due to size, direction or angle differences. You must manually reconnect the open connections.
|
|
FabricationPartFitFailure |
Fabrication Part Fitting Failed to Fit
|
|
FabricationPartHasInvalidGeometry |
The fabrication part either has no material or has badly configured dimensions, resulting in bad geometry.
|
|
FabricationPartInvalidConnection |
Fabrication Part connection invalid and could not be automatically coupled.
|
|
FabricationPartInvalidSpecification |
The part specification is invalid.
|
|
FabricationPartNoPartTypeFound |
There are no fabrication part types found for the current Configuration and Service. Please select settings and reload the service to create the fabrication part types.
|
|
FabricationPartNotAttachedToStraight |
The part must be attached to straight.
|
|
FabricationPartOptimizeInvalidConnection |
No available couplings to connect standard lengths for this instance of straight.
|
|
FabricationRodDetachFromHangerError |
The rod need to be detached from hanger.
|
|
FabricationRodsConnectionChangedWarning |
The structural component that the hanger is attached to has changed to a different element.
|
|
FabricationRodsDisconnectedError |
The hanger rod was disconnected because there is no structural component above.
|
|
FabricationRodsDisconnectedWarning |
The hanger rod was disconnected because there is no structural component above.
|
|
FabricationServiceMismatch |
Attempting to connect fabrication parts from different services.
|
|
FabricationStraigtLengthOversized |
Fabrication straight exceeds the standard length. Use the Optimize Length command to adjust the length.
|
|
FixedFabricationPartNotChangeLength |
Failed to change length of fixed part.
|
|
GroupedFabricationPartNotReposition |
Failed to reposition part.
|
|
HangerProfileNotMatchWithHost |
The defined hanger profile does not match with the host.
|
|
HangerWidthOutOfRange |
The hanger width is too large to show.
|
|
InvalidConnectionsHaveBeenDisconnected |
Invalid connections have been disconnected. Please reconnect them manually or use different fittings.
|
|
InvalidSelectionThereCannotBeOpenConnectors |
Invalid selection there cannot be any open connectors for the design to fabrication part tool.
|
|
NoStructuralHostToAttachWarning |
There is no structural component to attach the hanger rod to.
|
|
NotAllPartsWereConvertedUnsuportedFittingOffsets |
Not all parts were converted. Eccentric transitions and taps that have offsets from the center line are unsupported and cannot be converted.
|
|
PinnedFabricationPartNotChangeExtension |
Failed to change extension of part.
|
|
PinnedFabricationPartNotReposition |
Failed to reposition part.
|
|
PlaceCutinFittingFailed |
Failed to insert part.
|
|
SizeNotAvailableInFabricationService |
Sizes:%1!s! in system %2!s! are not available in fabrication service:%3!s!, All available sizes are:\n%4!s!.
|
|
UneditableFabricationPartNotReposition |
Failed to reposition part.
|